If there is a
non-IDE disk controller in your system, or you plan to use network
disks or external hardware devices,
first check the Hardware
Compatibility List.
If you plan to use any external device, turn it on before
starting the system.
If the motherboard in your computer supports the Serial ATA
(SATA) devices, but IDE disks are also present, only the SATA
devices should be set to the Enhanced Mode in BIOS.
1
|
Make sure that the first startup device in
the system BIOS is the device from which you plan to start your
computer (a CD/DVD drive or A (Floppy))
|
Refer to your
system documentation for details.
2
|
Insert the Agent
Emergency startup CD/DVD disc, a
removable device, or the first floppy disk and start your
computer |
>
|
Agent Emergency will start
and its prompt will appear |
If you start
your computer with floppy disks, you'll see prompts to insert a
next floppy disk.
-----------------------------------------------------------------
Booting R-Studio Emergency. Please wait...
Waiting 8 seconds for PCMCIA devices to settle
Booting R-Studio Agent Emergency. Now you may remove floppy.
-----------------------------------------------------------------
Querying DHCP to configure network interfaces...
Press ENTER within 10 seconds to configure them manually.
|
If your network has a DHCP
server
The computer running R-Studio Agent Emergency will be assigned an IP
address automatically
A prompt with a
computer address will appear. You need to remember it to access the
computer via network.
If your network does not have a DHCP
server
You need to
configure the interfaces and IP addresses manually.
1. A
prompt to select an interface will appear. Enter the selected
interface name and press Enter.
2. A
prompt to enter its IP address and optional subnet mask will
appear. Enter the IP address and optional subnet mask and
press Enter.
------------------------[ List of Interfaces ]--------------------------------
Name IP Address NETMASK Vendor
------------------------------------------------------------------------------
re0 Unconfigured RealTek 8139C+
------------------------------------------------------------------------------
# Enter interface name, 'gw' for default gateway or just press ENTER to finish
#>re0
# Enter IP address and optional NETMASK delimited by space
#>192.168.0.10 255.255.255.0
|
3. A
prompt to configure another interface, gateway, or to finish
configuring the interfaces will appear. Enter gw,
enter the IP address of the gateway, and press Enter.
------------------------[ List of Interfaces ]--------------------------------
Name IP Address NETMASK Vendor
------------------------------------------------------------------------------
re0 Unconfigured RealTek 8139C+
------------------------------------------------------------------------------
# Enter interface name, 'gw' for default gateway or just press ENTER to finish
#>re0
# Enter IP address and optional NETMASK delimited by space
#>192.168.0.10 255.255.255.0
------------------------[ List of Interfaces ]--------------------------------
Name IP Address NETMASK Vendor
------------------------------------------------------------------------------
re0 192.168.0.10 255.255.255.0 RealTek 8139C+
gw Unconfigured Default gateway
------------------------------------------------------------------------------
# Enter interface name, 'gw' for default gateway or just press ENTER to finish
#>gw
# Enter default gateway IP Address
#>192.168.0.1
------------------------[ List of Interfaces ]--------------------------------
Name IP Address NETMASK Vendor
------------------------------------------------------------------------------
re0 192.168.0.10 255.255.255.0 RealTek 8139C+
gw 192.168.0.1 Default gateway
------------------------------------------------------------------------------
# Enter interface name, 'gw' for default gateway or just press ENTER to finish
#>
|
4.
Press Enter to finish configuring the interfaces, or enter
the name of the next interface to configure.
>
|
Agent Emergency will show a
prompt that is ready to accept connections |
* R-Studio Agent started and ready to accept connections...
* You may press ENTER to start to remote R-Studio...
|
Now the computer
may be accessed by
via network.
When you need to connect R-Studio
and R-Studio Agent Emergency over
the Internet, it may be necessary to start the connection from the
computer where R-Studio Agent
Emergency is running.
To connect to
R-Studio's
computer,
1
|
Press the Enter key and enter the IP
address of the computer where R-Studio is running
as IPaddress:port. |
* R-Studio Agent started and ready to accept connections...
* You may press ENTER to start connection to remote R-Studio...
# Enter R-Studio IP address or just press ENTER to cancel> 192.168.0.25:80
|
The default port
is 8080, and you don't have to specify it.
2
|
Enter the password if required, and press
the Enter key. |
* R-Studio Agent started and ready to accept connections...
* You may press ENTER to start connection to remote R-Studio...
# Enter R-Studio IP address or just press ENTER to cancel> 192.168.0.25:80
# Enter password or just press ENTER to connect without one>PaSsWoRd1234
|
>
|
When the connection is established
successfully, R-Studio Agent
Emergency will notify you about
this. |
* R-Studio Agent started and ready to accept connections...
* You may press ENTER to start connection to remote R-Studio...
# Enter R-Studio IP address or just press ENTER to cancel> 192.168.0.25:80
# Enter password or just press ENTER to connect without one>PaSsWoRd1234
Connection with 192.168.0.25:80 is established successfully.
|
|